240-Degree 3-Head 3300 Lumen Dual Detection LED Motion-Activated Flood Light with Timer - White
See product page: 240-Degree 3-Head 3300 Lumen Dual Detection LED Motion-Activated Flood Light with Timer - White (SE1293-WH3-02LF0)
How do you reset unit?
Please watch our YouTube video, "Security Light Installation Part 11: How to Troubleshoot and Reset Your PIR," on how to reset the unit.
Is there a video to install this light?
Please click the link below. Video is for a different fixture, but installation is the same.
https://www.youtube.com/watch?v=ebv0C2qq6mU
My bottom sensor light blinks red and the 2 lights on top blink on and off rapidly. What can I do to fix this?
Please try resetting your fixture by following the instructions below. Please make sure the fixture is put into test mode prior to cutting power to the fixture. The fixture then needs to come on twice in test. Once when power is turned back on and a second time with motion. After this is successfully completed, you are reset, you can put it your desired settings. Do NOT leave the fixture in test. Please do NOT adjust the fixture after the reset, or toggle the wall switch. Give it at least 24 hours to reset and calibrate. If you have any issues with the fixture after or during the reset, please let me know right away.
Please note the fixture should not operate out of test mode in daylight hours due to the built in dusk to dawn sensor. Please note the third or fourth dial is your low beam area light. That will keep the fixture on from dusk to dawn, if you want this to operate strictly with motion, turn that setting off. If the fixture does not trigger with motion in test. Still take the fixture out of test, put in your desired settings, and see how it operates tonight. For SE1292 and SE1293 models, if you want the low beam area light off, change the setting to 3hrs prior to putting in test mode. Once you reset and take the fixture out of test, change the area light setting to off. While power is on change the area light settings to 3 hours, then put the fixtures into test mode.
Turn power off for 2-3 minutes.
Turn power on.
Lights should come on for 15-20 seconds then shut off.
After the lights shut off, try triggering in test. If they do not trigger that is fine.
Take the fixtures out of test, put in your desired settings.
Turn the area light off.
Please note the fixture should not operate out of test mode in daylight hours due to the built in dusk to dawn sensor. Please note the third or fourth dial is your low beam area light. That will keep the fixture on from dusk to dawn, if you want this to operate strictly with motion, turn that setting off. If the fixture does not trigger with motion in test. Still take the fixture out of test, put in your desired settings, and see how it operates tonight. For SE1292 and SE1293 models, if you want the low beam area light off, change the setting to 3hrs prior to putting in test mode. Once you reset and take the fixture out of test, change the area light setting to off. While power is on change the area light settings to 3 hours, then put the fixtures into test mode.
Turn power off for 2-3 minutes.
Turn power on.
Lights should come on for 15-20 seconds then shut off.
After the lights shut off, try triggering in test. If they do not trigger that is fine.
Take the fixtures out of test, put in your desired settings.
Turn the area light off.
The light stays off during the day which is fine. At dusk, the lights go on but never shut off. I have the light duration off and they still stay on. I do not have a motor or warm air stream. 2 other of your lights are also on the same circuit and work fine.
This fixture has a factory preset that has the area light feature on. Resetting the fixture should resolve your issue.
Please try resetting your fixture by following the instructions below. Please make sure the fixture is put into test mode prior to cutting power to the fixture. The fixture then needs to come on twice in test. Once when power is turned back on and a second time with motion. After this is successfully completed, you are reset, you can put it your desired settings. Do NOT leave the fixture in test. Please do NOT adjust the fixture after the reset, or toggle the wall switch. Give it at least 24 hours to reset and calibrate. If you have any issues with the fixture after or during the reset, please let me know right away.
Please note the fixture should not operate out of test mode in daylight hours due to the built in dusk to dawn sensor. Please note the third or fourth dial is your low beam area light. That will keep the fixture on from dusk to dawn, if you want this to operate strictly with motion, turn that setting off. If the fixture does not trigger with motion in test. Still take the fixture out of test, put in your desired settings, and see how it operates tonight. For SE1292 and SE1293 models, if you want the low beam area light off, change the setting to 3hrs prior to putting in test mode. Once you reset and take the fixture out of test, change the area light setting to off. While power is on change the area light settings to 3 hours, then put the fixtures into test mode.
Turn power off for 2-3 minutes.
Turn power on.
Lights should come on for 15-20 seconds then shut off.
After the lights shut off, try triggering in test. If they do not trigger that is fine.
Take the fixtures out of test, put in your desired settings.
Turn the area light off. Or to desired setting.
Please note the fixture should not operate out of test mode in daylight hours due to the built in dusk to dawn sensor. Please note the third or fourth dial is your low beam area light. That will keep the fixture on from dusk to dawn, if you want this to operate strictly with motion, turn that setting off. If the fixture does not trigger with motion in test. Still take the fixture out of test, put in your desired settings, and see how it operates tonight. For SE1292 and SE1293 models, if you want the low beam area light off, change the setting to 3hrs prior to putting in test mode. Once you reset and take the fixture out of test, change the area light setting to off. While power is on change the area light settings to 3 hours, then put the fixtures into test mode.
Turn power off for 2-3 minutes.
Turn power on.
Lights should come on for 15-20 seconds then shut off.
After the lights shut off, try triggering in test. If they do not trigger that is fine.
Take the fixtures out of test, put in your desired settings.
Turn the area light off. Or to desired setting.
Does the color code for line and load have to match plug?
No it does not matter what row you plug your wires into, but we recommend that you put ALL the wires into the same row.
More importantly, you need to make sure that the supply wires from the house match (in color) with the wires coming from the fixture.
Can this be installed under the eaves? I don't see any way to arrange the lights/motion sensors to work when the kit is mounted to a horizontal surface.
Yes. This fixture is suitable for an eave installation. There should be an image on the box and instructions in the owner's pamphlet.
Where do I buy a replacement sensor?
The sensor is not a replaceable part.
Will this dual light operate from dusk to dawn on low level brightness and then increase to the brighter level when motion is detected for a preset period of time
You can set the low beam area light for dusk to dawn, 3 hours, 5 hours, or off.
What kind of light bulbs does it use and how do you replace them
This is an LED fixture. It does not contain light bulbs.
How do you wire this light with multiple fixtures on the same circuit?
The fixture can be installed on the same circuit with other LED devices, but has to be wired in parallel.
Is there a maximum temperature that this product can withstand?
45 degrees celcius.
Is there a "minimum" temperature the light works properly?
This light is cold weather rated with a minimum cold start temperature of negative 20°F
How much power does the SE1293-WH3 use on low beam and high beam settings?
37 watts high beam, 10 watts low beam
How do I get to the controls to change the distance for detection
Did you find what you were looking for?