240-Degree 2-Head 2500 Lumen Dual Detection LED Motion-Activated Flood Light with Timer - Bronze

Model
SE1292-BP2-02LF0
Rating:
84 % of 100

This Good Earth Lighting LED flood light provides safety and security for the home by illuminating dark exterior areas, such as backyards and driveways. This light specifically features no blind spots with its innovative Downfire™ technology. The light shines in front and directly below the fixture expanding light downward, casting light on difficult-to-light areas. This has a 2N1 adjustment control allowing for two levels of light with high or low beam light and automatic nighttime lighting with motion detection, offering in 3 color tunable white selection. The adjustable timer and range controls allow for maximum customization with an option for manual override, disabling automatic nighttime lighting features to operate from a light switch inside the home. The Set to Go feature has preset out of the box, no testing required, with detection range of 50 feet with 3-minute timer in 5000K daylight. IP65-rated, this light is ideal for outdoor wet locations; it's also cold weather rated with a minimum cold start temperature of negative 20°F. This light is safety tested and has a 10-year limited warranty. This light is an upgrade of SE1084.

Specification
Related Model SE1292-BP2-02LF0-G, 3665664
Fixture Material Die-cast Aluminum
Fixture Color Satin Aged Bronze
Glass/Lens Type Diamond Pattern
Mounting Wall/Eave/Surface/Recessed Mount
Motion Detection Range 240 degrees up to 100 ft and 360 degrees below
Two Level Lighting Yes
Two Detection Zone Yes
Light Coverage Spread: 49.21 ft; Distance: 50.85 ft
Safety Rated Wet Location
Safety Listing ETL
Energy Star No
Light Included Yes
Light Source LED
LED Qty 56
Color Temperature 3000K/4000K/5000K Selectable
Color-Changing Temperature Yes
Color Rendering Index (CRI) 80
Rated LED Life 50,000 hours
Specification
Lumens 2500 Security/800 Area
Dimmable No
Input Voltage 120V, 60Hz
Input Wattage 30
Battery Included No
Power Cord None - Direct Wire
Linkable No
Power Switch Wall Switch
Power Source Direct Wire
Warranty 10-Year Limited Warranty
Fixture Dimensions (inches) 11.19 x 6.1 x 7.68
Fixture Weight (lbs) 2.14
Write Your Own Review
You're reviewing:240-Degree 2-Head 2500 Lumen Dual Detection LED Motion-Activated Flood Light with Timer - Bronze
Your Rating
Customer Questions
We bought SE1292-BP2-02LF0-G and turned the Select AREA LIGHT to off but the light is still on all night. We have already tried to turn the unit off and and to turn the test mode off and on to enable the unit to reset itself but it has not worked.
Please reach out to customer service at 1-800-291-8838 for technical support and/or warranty replacement. We are available Monday through Friday 8:30 am to 5:00 pm CST.
I’m having trouble figuring out how to eave mount. With the sensor facing forward, you cannot rotate the lights to be oriented up. Nothing in the instructions.
Can this light be on dusk to dawn at a lower light level and then go to a higher output if motion is detected?
Turn the AREA LIGHT MODE control knob to either 3 hours, 5 hours, or Dusk-to-Dawn. The 3-hour setting turns the Area Light on at dusk for a duration of 3 hours. The 5-hour setting turns the Area Light on at dusk for a duration of 5 hours. The Dusk-to-Dawn setting turns the Area Light on at dusk for the duration of the night until it shuts off at dawn. The OFF setting disables the Area Light feature completely, and fixture operates strictly as a security light triggered by the motion sensor (PIR). The Area Light is low beam. The fixture will jump to high beam when triggered by motion.
I just bought model SE1292-BP2-02LF0, which I have to eave mount. I am unable to point the motion sensor and the lights in the same direction. It would help if I could swap the left and right lights.
Please click the link below to view our installation video on eave mounting: Security Light Installation Part 5: Eave Mount Installations
I just bought model SE1292-WH3-02LF0-G, which I have to eave mount. I am unable to point the motion sensor and the lights in the same direction. It would help if I could swap the left and right lights. The lamps holders are offset so that rotating them to point down causes them to interfere with each other.
Since this is a waterproof (IP65) fixture you can ignore the "this side up" on the light heads. That should help with eave installation.
I set the light up to my desired settings and it worked great until the power went out briefly and the light reverted to its factory settings. I reset it and it worked fine until I turned off the power and it again reset to the factory settings. I have to set up a ladder to reset the test button each time. Is there any way that it can be set to hold my settings even if the power is interrupted?
Unfortunately if power is cut to the fixture for an extended period of time it may revert back to factory settings.
Can you tape off part of the motion sensor to avoid tree limb movement?
You can repositioning the motion sensor, adjusting your sensitivity/distance, or try covering it with electrical tape to cut down on false triggers.
With the motion sensor range set at 60', the duration set at 2 minutes, the dusk to dawn turned off. The sensor is tilted slightly downward towards the end of a 40' driveway. I can walk up to the light and it fails to turn on, I wave a broom in front of the light and it still fails to turn on. I then walk away from the light and it turns on for the two minute period. How do I correct the fact it failed to see me when I walked right up to it?
You may be walking in a grey zone or blind spot and may need to adjust the PIR sensor. Security Light Installation Part 7: Tips on Aiming Your PIR - YouTube
Did you find what you were looking for?

CA Residents:   Prop 65 Warning(s)